Just How to Replace a Bathtub in Your Bathroom
Just How to Replace a Bathtub in Your Bathroom
Blog Article
The article down below in relation to How to Install a Bathtub Yourself is absolutely informative. Read on and draw your own ideas.
Mounting a bath tub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably tough job. If the old tub is readily accessible, the project can move rapidly; if you need to open up a wall surface to eliminate the old tub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old bathtub as well as embeded in the brand-new one. Make certain you have qualified yourself for the job and are comfortable trying it. As opposed to employing a contractor to take over a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will certainly aid you mount a brand-new bath tub in your bathroom if you have actually currently bought a brand-new bathtub and don't require to alter the plan of your previous water system pipes.
Your tools and product list ought to make up the following:
Planning for the Setup
First of all, the supporting structure provided with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited access that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old sealing substance.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, position the bathtub in the required position. The wooden boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and also readjusting the feet on the bath tub till the level reviews degree.
To set up taps, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the water supply and also examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the bath tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bath tub must wait until the bathtub has actually been utilized at least when as this will resolve it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin making sure that the washers are in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap finishes first, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, triggering the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with wetness and also possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill up the bathtub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can fracture fairly early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently available on the market. It is a good idea to fit the floor tiles using waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I recently found that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while surfing the web. Sharing is nice. One never knows, you may be doing someone a favor. Kudos for your time. Visit us again soon.
Recurring Service Plans Report this page